Browse all practice questions for the Special Inspector (SI) Certifications Fireproofing Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Special Inspector (SI) Certifications Fireproofing Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What can be done when SFRM bond strength tests are extremely difficult to accomplish?
  • What is the minimum allowable radius for the test cap used in SFRM bond strength testing?
  • What is the inspector’s role regarding change orders affecting fireproofing?
  • What term is used to describe items not meeting project requirements in field inspection?
  • How many TFIFRM thickness readings are required for a pipe column?
  • In the given project scenario, how many columns and beams must be tested for bond strength?
  • High rise buildings that are 410 feet tall must have an SFRM bond strength of at least how many psf?
  • List two common non-destructive test methods for verifying thickness of fireproofing.
  • The minimum unit used to express metal lath weight in SFRM applications is which?
  • How should inspectors manage areas like stairs and elevator shafts where fireproofing is applied?
  • What is the minimum allowable temperature during TFIFRM curing?
  • What should be included in a daily field inspection report for fireproofing?
  • Which statement best describes patching around penetrations as required by spec?
  • In SFRM primer qualification, which statement is true about the relationship between primer bond strength and steel bond strength?
  • If primer is used on a column beneath SFRM, the maximum permissible column web depth is 16 inches. Which option is correct?
  • Density test samples must be at least how many cubic inches?
  • Why is thermal expansion consideration important for fireproofing?
  • What is the allowable SFRM bond strength test cap diameter range?
  • In a hypothetical scenario where the steel bond strength is 500 psf, what must the average primer bond strength meet?
  • How many SFRM thickness measurements are required for a metal deck that uses a flat plate?
  • Which factors influence the cure times for spray-applied fireproofing?
  • What is meant by a "thermal boundary" in relation to structural fireproofing?
  • What can be used instead of metal lath to create a mechanical break between SFRM and the substrate?
  • In SFRM density testing, the dry weight is measured to the nearest 0.1 g.
  • If a high rise building receives SFRM and is 430 feet in height, what is the minimum required SFRM bond strength?
  • A tube steel column is required to have 1 inch of SFRM thickness. What is the lowest allowable individual thickness measurement?
  • A wide flange column is required to have 2 inches of SFRM thickness. What is the lowest allowable individual thickness measurement?
  • A column requires a mil thickness of 65 mils for TFIFRM. What is the lowest allowable mil thickness for an individual thickness determination?
  • What is the maximum allowable relative humidity when drying SFRM for density testing?
  • If the bond strength of SFRM on steel is 500 psf, what must the average bond strength of SFRM on the primer meet?
  • Why is surface cleanliness critical for fireproofing adhesion?
  • Why are curing conditions critical in cementitious fireproofing?
  • How should inspectors address extreme weather conditions affecting curing?
  • How many TFIFRM thickness determinations are required for a W-shape column?
  • What is the minimum allowable radius of the test cap used in SFRM bond strength testing?
  • What is the potential impact of corrosion under insulation in contact with fireproofing?
  • The deck thickness test area is reported using which unit of area?
  • Which option best describes the TFIFRM inspector's deliverables?
  • Distinguish between thickness and coverage in fireproofing inspection.
  • The bond strength testing method described in Technical Manual 12-A can be used up to what bond strength?
  • The bond strength test method for SFRM described in Technical Manual 12-A can only work for products up to what bond strength?
  • When metal lath is used for SFRM application, it must weigh at least how many pounds per cubic yard?
  • Describe a typical process for performing a pull-off adhesion test on fireproofing.
  • What is the minimum allowable test area for SFRM thickness?
  • For high-rise structures at 410 feet, the required SFRM bond strength is at least 430 psf. Which option is correct?
  • A beam requires a mil thickness of 65 mils for TFIFRM. What is the lowest allowable average mil thickness for the beam?
  • When testing SFRM thickness on a joist, 7 thickness measurements are taken at each end of a ___ length.
  • Which statement best describes sprayed fireproofing product types?
  • When qualifying a primer to be used beneath SFRM, what is the minimum allowable bond strength of SFRM on the primer?
  • During thickness testing, what should you do if the surface has excessive irregularities?
  • In case of moisture-related delamination, what documentation should inspectors prepare?
  • What defines the typical safe working temperature range for applying cementitious fireproofing?
  • Which of the following is within the TFIFRM inspector's scope of work?
  • For metal decking totaling 9,100 square feet, how many SFRM thickness tests are required?
  • For beams requiring 48 mils, what is the minimum permissible average TFIFRM thickness?
  • Which document governs installation requirements for fireproofing in most commercial buildings?
  • What does SA 2.5 refer to in ISO 8501-1?
  • For SFRM application, substrate temperatures must be maintained at 40 degrees F for how long after application?
  • When is it appropriate to document change decisions related to fireproofing?
  • When must SFRM test reports be submitted?
  • What is the importance of surface roughness for adhesion?
  • When can TFIFRM thickness tests be taken?
  • What is the difference between cementitious and intumescent fireproofing?
  • What forms of protection help prevent damage to fireproofing before final inspection?
  • What is the inspector’s role regarding shop drawings for fireproofing?
  • What is the minimum size required for an SFRM density test sample?
  • What is delamination in fireproofing?
  • For SFRM applications, substrate temperatures must be maintained at 40 degrees Fahrenheit for 24 hours. Which option reflects this statement?
  • For patching SFRM repairs on a project, which material is permitted?
  • Explain the term 'rebound' in spray-applied fireproofing.
  • Which of the following is NOT listed as a common sprayed fireproofing product?
  • The minimum size for a density test sample is 8 cubic inches. Which option matches?
  • How should transition areas around beams be treated?
  • During an inspection, what is the minimum number of TFIFRM gauge thickness accuracy checks required?
  • What should be done where penetrations or openings pass through fireproofed elements?
  • When testing SFRM thickness on a beam, ___ thickness measurements are taken at each end of a ___ length.
  • During bond strength testing of SFRM, the rate of force should be about:
  • What is the focus of a post-installation inspection for fireproofing?
  • When would a drill bit be used for SFRM inspection?
  • How should cure status be assessed during inspection?
  • When applying SFRM to beams beneath decking, what level of SFRM is placed in the void between beam and deck flutes?
  • How should an inspector handle an unapproved substitution of fireproofing material?
  • What surface prep level is typically required for steel to receive spray-applied fireproofing?
  • Which testing standard covers SFRM thickness testing?
  • In the roof framing example, what is the total number of structural members (columns plus beams)?
  • In the SFRM bond strength example, which test cap area was used?
  • Which of the following is NOT listed as a factor influencing cure times for spray-applied fireproofing?
  • What percent of specified thickness is the minimum allowable TFIFRM thickness determination?
  • If a transition area in the beam zone does not meet thickness and coverage requirements, what action is required?
  • What is the purpose of verification of revised thickness or product after a change order?
  • Which statement about field-applied fireproofing is true?
  • If 9 thickness measurements are taken at each end of a 12-inch beam segment, how many total measurements are recorded?
  • Why is material compatibility important between fireproofing and cladding systems?
  • The statement 'The minimum TFIFRM thickness determinations must be 80% of the specified thickness' is true.
  • Which type of failure describes a separation between SFRM and substrate?
  • Which statement describes a commonly observed sprayed fireproofing product option?
  • What is the purpose of a cure window in fireproofing?
  • When testing a W-shaped column for SFRM thickness, the specified thickness is 1-7/16 inch. 2 of the measurements are 1-3/16 inch and 1-1/4 inch while the rest are above 1-7/16 inch. Is this acceptable?
  • What is the maximum relative humidity of a drying oven when drying SFRM density samples?
  • What is the difference between factory-applied and field-applied fireproofing?
  • Which item is not typically verified on a fireproofing product data sheet (PDS)?
  • What percentage of TFIFRM containers must be labeled with the manufacturer and product names?
  • What properties should be verified on a product data sheet (PDS) for fireproofing?
  • What documentation is required for fireproofing to verify compliance?
  • When measuring tube steel SFRM thickness, how many measurements can be less than the specified thickness?
  • The curing temperature minimum for TFIFRM is 50 degrees F. Which statement is true?
  • What is the purpose of protective coverings during fireproofing installation?
  • When can visual inspection of TFIFRM take place?
  • What humidity level is allowed when drying SFRM for density testing?
  • Which statement best describes the cure period defined by product data sheet?
  • If there are 100 columns on a floor that receive SFRM, how many must be thickness tested?
  • Which installation conditions could lead to improper curing of cementitious fireproofing?
  • When testing SFRM thickness, what should be done if there are excessive irregularities on the surface?
  • Which of the following is allowed on substrates beneath SFRM?
  • For joist thickness testing, how many thickness measurements are taken at each end of a 12 inch length?
  • How do penetrations or fixtures affect fireproofing thickness requirements?
  • For SFRM thickness testing on a deck, the test area is a square with a side length of how many inches?
  • A building has 15,010 sf of metal decking at the roof level that receives SFRM. How many thickness tests must be taken on the deck?
  • How do intumescent coatings behave when exposed to high temperatures?
  • Suppose the required TFIFRM thickness for a truss is 50 mils. What is the maximum thickness determination you can record on the report?
  • What is the maximum allowable relative humidity of the work area when placing TFIFRM?
  • When drying SFRM for density testing, what is the maximum allowable relative humidity?
  • A TFIFRM thickness testing project is 13,500 sf and has columns, primary beams, secondary beams, and trusses. How many thickness tests do you perform?
  • How should overspray and rebound be managed on a job site?
  • What reading precision must SFRM thickness gauges be capable of reading to?
  • If primer is used on a column beneath SFRM, the column web depth cannot exceed how many inches?
  • What is the SFRM bond strength if the test cap area is 0.0576 square feet and the force at SFRM failure is 15 pounds?
  • Which of the following best describes patching requirements for SFRM on a project?
  • How long must substrate temperatures be maintained after applying TFIFRM?
  • What is the role of the Special Inspector in fireproofing?
  • What is the minimum allowable average TFIFRM thickness for a beam that requires 48 mils of thickness?
  • Which statement best describes how moisture content affects bonding potential during fireproofing application?
  • Which of the following are not allowed when performing thickness testing on TFIFRM?
  • Suppose the roof framing of a building receives SFRM and has 24 columns and 42 beams. how many members must be tested for thickness?
  • Which test is used to measure bond strength between fireproofing and the substrate?
  • Which of the following should the Special Inspector document when non-conformances are observed?
  • Differentiate thickness coverage from coverage uniformity.
  • Which statement best describes the effect of a rough surface on fireproofing adhesion?
  • If there are irregularities on the SFRM thickness test surface, what is the recommended action?
  • Why is maintaining FR rating around penetrations critical?
  • What is the unit used to express SFRM bond strength in tests?
  • Which SFRM testing method uses polystyrene beads?
  • What does NFPA 285 test in relation to fireproofing installations?
  • A joist is tested for SFRM thickness. How many of the thickness measurements can be less than the specified thickness?
  • On a W-shaped column with specified thickness 1-7/16 inch, if all but two measurements exceed 1-7/16 inch, and the two below are 1-3/16 and 1-1/4 inch, the specimen is acceptable.
  • What types of damage must be protected from after installed fireproofing?
  • How many total SFRM thickness measurements are taken on a joist?
  • Explain the difference between a thermal barrier and fireproofing?
  • Which statement is true about TFIFRM thickness determinations for a column specified at 65 mils?
  • How should suspected delamination due to moisture be handled?
  • In TFIFRM thickness testing, what is the lowest allowable mil thickness for an individual thickness determination on a column specified at 65 mils?
  • Which type of failure describes a separation within SFRM?
  • When testing SFRM thickness on a deck, what is the square area of the test area?
  • Which of the following documents is not typically required to verify fireproofing compliance?
  • Which is a common cause of delamination between fireproofing and the substrate?
  • What is a key consideration when patching fireproofing during post-installation inspection?
  • What is the typical purpose of on-site field reports in fireproofing projects?
  • Which statement about SFRM thickness testing is correct?
  • TFIFRM thickness tests must be performed when TFIFRM has stabilized. Which option correctly reflects this timing?
  • According to Technical Manual 12-A, SFRM test reports must be submitted to:
  • How many SFRM thickness tests are required underneath metal decking that is 6,500 sf?
  • What does "as-built thickness" refer to during inspection?
  • For an area of 8,000 square feet on the 3rd floor, how many columns and beams must be tested for bond strength?
  • What is the typical purpose of spray-applied cementitious fireproofing?
  • Where do you find the requirements for applying TFIFRM?
  • What construction detail can be used to create a mechanical break between SFRM and the substrate instead of metal lath?
  • What is the minimum required amount of TFIFRM gauge thickness accuracy checks during an inspection shift?
  • What is an adhesion test and which standard is commonly used?
  • How does moisture content in the substrate affect fireproofing application?
  • Which statement correctly describes when a visual inspection of TFIFRM should occur?
  • Why are fire resistance rating tests important for fireproofing products?
  • Name two critical design considerations when specifying cementitious spray-applied fireproofing on steel.
  • When drying SFRM for density testing, what is the maximum allowable temperature?
  • In density testing of SFRM, the dry weight is measured to the nearest what?
  • What is the purpose of patching after initial spray?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy